Power Inverter APS X Series Inverter/Charger with Auto-Transfer Switching and Line Interactive Voltage Regulation

 

Model #: APSX6048VR

	48V DC or 208/230V (selectable) AC input; 208/230V, 50/60 Hz, pure sine wave output (hardwired)
	6000 watts continuous, 9000 watts OverPower™ and 12000 watts DoubleBoost™ inverter output (see specifications)
	3-stage, 23/90 amp selectable wet/dry cell battery charger
	Auto Transfer Switching option for battery backup / UPS operation - includes wired APSRM4 remote control switch
	Automatic Voltage Regulation corrects brownouts and overvoltages without using battery power
	High reliability large-transformer design with protected DC and AC wiring terminals

• APSX6048VR serves as an automotive or stationary DC-to-AC inverter with automatic line-to-battery transfer and integrated battery charger
• Supports 208 or 230V AC output from a 208 or 230V AC line power source or 48V DC battery source
• Automatic transfer between line and battery power supports UPS protection during blackouts and severe voltage fluctuations for equipment compatible with a selectable full or 1/2 cycle transfer times
• 6000 watts continuous sinewave AC output in inverter mode
• Double Boost™ inverter output supports momentary startup loads up to 200% of the continuous rating for up to 10 seconds (see specification chart)
• OverPower™ inverter output supports longer duration overloads to 150% for up to 60 seconds under ideal battery and temperature conditions. (For best results, utilize OverPower usage for as short of a duration as possible, ensure battery bank and cabling is able to provide full nominal DC voltage under load and allow inverter/charger to fully cool before and after OverPower usage.)
• 3 stage, selectable 23/90 amp battery charger with adjustable settings for wet/gel battery types offers fast, reliable battery recharging
• Protected DC hardwire bolt-down input lugs safely accept heavy gauge DC input wiring from attached battery bank
• Protected hardwire AC output passes 208/230V line or inverter power sinewave AC output through to connected equipment
• Reliability enhanced large-transformer design with protected DC wiring terminals
• Moisture-resistant construction enables vehicular or marine operation in high humidity environments
• 3 position operating mode switch supports "AUTO" mode to enable automatic transfer between DC and AC modes, CHARGE-ONLY to maintain a full battery charge when AC is present without auto transfer and SYSTEM OFF settings
• Set of six front panel LEDs display AC/DC operational modes, overload status, DC voltage level, shutdown status and system fault status
• Set of 4 configuration dip switches support AC input selection of 208/240V, selectable 50 /60Hz frequency, and selectable full or half cycle transfer times
• Set of 4 configuration dip switches support wet/gel battery charging profiles, adjustable 235/245V (208V) / 260/270V (230V) high voltage auto transfer during overvoltages and selectable 165/175V (208V) / 170/180V (230V) AC low voltage auto transfer during brownouts
• Set of 4 additional configuration dip switches support battery equalization program and battery charger low / high settings
• Automatic thermostatically controlled multi-speed cooling fans protect the inverter from load and temperature related failures
• Grounding lug properly connects the inverter/charger system to earth ground or vehicle grounding system
• Automatic overload and thermal shutoff safely turns off inverter as excessive loads or overheating conditions develop
• Front panel remote control connector enables remote off/on switching (APSRM4 sold separately). Optional APSRM4 accessory also includes user configurable jacks to support inverter shutoff or startup as a vehicle ignition is engaged
• Load sensing control dial enables adjustable load threshold required to automatically turn the inverter on and off in DC mode as load conditions change
• Automatic Generator Starter jack enables user configuration of automatic generator startup as inverter batteries drop to 46.0 VDC and generator shutoff as inverter batteries are recharged to 56.4 VDC.
• Remote battery temperature sensing connection function prolongs battery life by adjusting the charge float voltage level based on battery temperature

TYPICAL APPLICATIONS

Versatile inverter/charger system with auto-transfer switching serves as an automotive inverter for RVs, over-the-road trucking, conversion vans and fleet service vehicles; a standalone alternative power source for off-grid, alternative energy or export applications and as an uninterruptible power supply (UPS) for items compatible with selectabe half-cycle (10ms) or full-cycle (20ms) transfer times.

OPTIONS & ACCESSORIES

98-121: 12 volt / 75 amp-hour battery BP260: Battery cabinet that holds two 98-121 batteries; order 98-121 batteries separately APSRM4: Wired Remote Switch controls the inverter/charger output power; 50 ft. cord; diagnostic LEDs; ignition interlock power control

PACKAGE INCLUDES

APSX6048VR Inverter/Charger Instruction manual with warranty information